LOCKSMITH CHARLEY EMERGENCY MOBILE SERVICE THROUGHOUT THE VALLEY 602-717-5397   CALL ANYTIME!

Locksmith Charley - Home Page                                      Main Transponder Page                                         Contact Locksmith Charley

 

Many of the key blank listings on this website are linked to a table containing cross-reference information and photographs.
ILCO is an aftermarket  manufacturer of key blanks.
STRATTEC is an Original Equipment Manufacturer (OEM) of key blanks for many automobile manufacturers. 
STRATTEC makes many remote headed key blanks that ILCO and others do not make.
Some of the links under the ILCO column may link to and display photographs of keys actually manufactured by STRATTEC or others. Any time a key blank reference is made in RED that is an indication that it is an OEM Part Number and it is typically available only from a dealer or possibly used from another source.

GM VATS keys contain a resistor pellet valued numerically at #1 - #15.
You must use the correct value resistor for your car or it will not start or run.

DISCLAIMER / DONATIONS

CLICK HERE FOR
HONDA / ACURA General notes and Emergency Starting Procedures

ACURA VEHICLES

HONDA VEHICLES

ACURA / HONDA KEYS

ILCO	STRATTEC	Description	Photos
HD106-PT	692246	Honda Transponder Key Use HD103 as test key
HD106-PT5	692057	Same as above but re-writable or Cloneable
HO03-PT HD112-PT	5907553 5913982	Honda / Acura High Security transponder key. "V" Transponder chip
HD111-PT	5907552	Honda / Acura transponder key. "V" Transponder chip
HD113-PT		Honda / Acura High Security transponder key. "H" Transponder chip
HO01-PT	692247	High Security Honda/Acura transponder key Fixed Code  type 13 chip
HO01-PT5	692082	High Security Honda/Acura transponder key Fixed Code Clonable - Read/Write

CLICK HERE FOR
HONDA / ACURA General notes and Emergency Starting Procedures

DISCLAIMER / NO WARANTY ON INFORMATION / DONATIONS

I have taken great care to try to ensure that all information presented on these web pages is factually accurate.

My intent is to use this web page in the place of several books as my source of reference. I am making this, my own personal reference source available to the general public as a courtesy and as a learning tool for people interested in the subject matter.

Accessing these pages and using the information presented here is done AT YOUR OWN RISK and I make NO WARRANTIES or GUARANTEES of ACCURACY or COMPLETENESS.

You understand and agree that the information presented on this website is a compilation of information from multiple sources that occasionally conflict one another. You understand that vehicle manufacturers frequently make mid-year changes and that the manufacturers and suppliers of after-market parts and information are frequently not directly provided with any information by vehicle manufacturers.

Your use of this website and any information contained herein constitutes your waiver of any liability or damages of any kind and you agree to indemnify and hold harmless Charles Eastwood, Locksmith Charley, his assignees and successors from any liability or damages which you might sustain from the use of this information.

If you find the information on this page helpful, donations are happily accepted.

You are encouraged to contact me by telephone at 602-717-5397 preferably from 10AM-Midnight California time. You can also contact me by E-Mail to:  Charley@LocksmithCharley.com. Please make sure to include you e-mail address and a telephone number so I can contact you back if there are any questions I need to get answered or to clarify any information.

This page is Copyrighted 2001-2013, by Charles "Locksmith Charley" Eastwood, CRL

 Honda / Acura General Notes and Emergency Starting Procedures

ACURA   VEHICLES - GENERAL NOTES

1. Any Acura CL, RL or TL that has a 3.5L engine is a Type 1 Honda/Acura product.
When originating new keys for a vehicle in which all existing keys have been lost, a new ECU must be installed*.
Once installed, TKO owners will be capable of originating new keys for these vehicles.
2. Any Acura CL, RL or TL that has a 3.2L engine is a Type 2 Honda/Acura product. These vehicles do not need to have their ECU replaced when all keys have been lost and new keys need to be originated.
3. Acura’s that contain Type 3 & 4 modules can be programmed by using the TKO and the standard OBDII cable D922876ZR. No additional hardware or software is required.
4. TKO owners must be aware that Ilco HD106-PT5 and HO01-PT5 keys cannot be added to Acura vehicles with the TKO unless they are pre-coded by way of the RW2, RW3, RW4 device. This function is only available on the RW2 with version 23.0 software. Pre-coded Acura blanks; HD106-PT and HO01-PT are now available from Ilco.

* It is possible to FLASH the Honda / Acura ECU to accept new keys.
Locksmith Charley can perform this flashing operation on-scene.

ACURA EMERGENCY ENGINE START PROCEDURE: (CL, TL & INTEGRA)

1. Make a mechanical key that will work the ignition lock cylinder.
2. Have the customer get the “Immobilizer Brake Code” from the dealer or Honda Customer Relations. You will need the Vehicle Identification Number. This is a five digit number code. Each car has a different “Immobilizer Brake Code” since they are VIN specific.
3. Turn the ignition switch to the ON position (II).
4. Have the BRAKE CODE in front of you. To enter the first number of the BRAKE CODE, press and release the brake pedal the same number of times as the first number in the BRAKE CODE. For example if the first number in the BRAKE CODE is a 2, press and release the brake pedal 2 times.
5. Turn the ignition switch to the LOCK position.
6. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 2nd number in the BRAKE CODE.
7. Turn the ignition switch to the LOCK position.
8. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 3rd number in the BRAKE CODE.
9. Turn the ignition switch to the LOCK position.
10. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 4th number in the BRAKE CODE.
11. Turn the ignition switch to the LOCK position.
12. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 5th number in the BRAKE CODE.
13. Turn the ignition switch to the LOCK position.
14. After entering the 5th number, the Immobilizer Indicator light on the dash should flash 5 times and then shut off. The car should now start. This procedure must be repeated each time you turn off the car for more than 10 minutes. The Immobilizer System indicator will remain on while the engine is running.
IMPORTANT NOTE: If the customer finds his/her keys or drives home to get them, they cannot use them until the vehicle has been turned off for more than 10 minutes.

ACURA EMERGENCY ENGINE START PROCEDURE: (3.5RL & NSX)

1. Make a mechanical key that will work the ignition lock cylinder.
2. Have the customer get the “Immobilizer Brake Code” from the dealer or Cross Country Motor Club at 1-800-594-8500, you will need the Vehicle Identification Number. This is a five digit number code. Each car has a different “Immobilizer Brake Code” since they are VIN specific.
3. Turn the ignition switch to the ON position (II).
4. Have the BRAKE CODE in front of you. To enter the first number of the BRAKE CODE, press and release the Parking Brake the same number of times as the first number in the BRAKE CODE. For example, if the first number in the BRAKE CODE is a 2, press and release the Parking Brake 2 times.
5. Turn the ignition switch to the LOCK position.
6. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 2nd number in the BRAKE CODE.
7. Turn the ignition switch to the LOCK position.
8. Within 30 seconds turn the ignition switch to the ON position (II) and enter the 3rd number in the BRAKE CODE.
9. Turn the ignition switch to the LOCK position.
10. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 4th number in the BRAKE CODE.
11. Turn the ignition switch to the LOCK position.
12. Within 0 seconds, turn the ignition switch to the ON position (II) and enter the 5h number in the BRAKE CODE.
13. Turn the ignition switch to the LOCK position.
14. After entering the 5th number, the Immobilizer Indicator light on the dash should flash 5 times and then shut off. The car should now start. This procedure must be repeated each time you turn off the car for more than 10 minutes.
IMPORTANT NOTE: If the customer finds his/her keys or drives home to get them, they cannot use them until the vehicle has been turned off for more than 10 minutes.

HONDA  VEHICLES - GENERAL NOTES        (2001 CIVIC BELOW)

1. All Honda Preludes (1997-01) use a Type 1 Honda module. When originating new keys for a vehicle in which all existing keys have been lost, a new ECU must be installed*.
Once installed, TKO owners will be capable of originating new keys for these vehicles.
2. All Honda’s using Type 2 or 3 modules can be programmed with the TKO and the D922876ZR OBDII cable. No additional hardware is required for these vehicles.
3. The 2003-04 Honda Accord is not compatible with the Ilco HO01-PT transponder key. These vehicles require the Honda original key available through Honda only. The original Honda key can be programmed with the TKO tool.
4. TKO owners must be aware that Ilco HD106-PT5 and HO01-PT5 keys cannot be added to Honda vehicles with the TKO, unless they are pre-coded by way of the RW2 device. This function is only available on the RW2 with version 23.0 software. Pre-coded Honda blanks; HD106-PT and HO01-PT are available from Ilco.

* It is possible to FLASH the Honda / Acura ECU to accept new keys.
Locksmith Charley can perform this flashing operation on-scene.
 

EMERGENCY START PROCEDURES FOR HONDA

1. Make a mechanical key that will work the ignition lock cylinder.
2. Have the customer get the “BRAKE CODE” from the dealer or Honda Customer Relations, you will need the Vehicle Identification Number. This is a five digit number code. Each car has a different “BRAKE CODE’ since they are VIN specific.
3. Turn the ignition switch to the ON position (II).
4. Have the BRAKE CODE in front of you. To enter the first number of the BRAKE CODE, set and release the emergency brake the same number of times as the first number in the BRAKE CODE. For example, if the first number in the BRAKE CODE is a 2, set and release the emergency brake 2 times.
5. Turn the ignition switch to the OFF position (0).
6. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 2nd number in the BRAKE CODE.
7. Turn the ignition switch to the OFF position (0).
8. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 3rd number in the BRAKE CODE.
9. Turn the ignition switch to the OFF position (0).
10. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 4th number in the BRAKE CODE.
11. Turn the ignition switch to the OFF position (0).
12. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 5th number in the BRAKE CODE.
13. Turn the ignition switch to the OFF position (0).
14. After entering the 5th number, the Immobilizer Indicator light on the dash should flash 5 times and then shut off. The car should now start. This procedure must be repeated each time you turn off the car for more than 10 minutes.
EMERGENCY START PROCEDURES FOR HONDA (ACCORD, INSIGHT, ODYSSEY & S2000)
1. Make a mechanical key that will work the ignition lock cylinder.
2. Have the customer get the “IMMOBILIZER BRAKE CODE” from the dealer or Honda Customer Relations, you will need the Vehicle Identification Number. This is a five digit number code. Each car has a different “BRAKE CODE” since they are VIN specific.
3. Turn the ignition switch to the ON position (II).
4. Have the BRAKE CODE in front of you. To enter the first number of the BRAKE CODE, press and
release the brake pedal the same number of times as the first number in the BRAKE CODE. For example if the first number in the BRAKE CODE is a 2, press and release the brake pedal 2 times.
5. Turn the ignition switch to the LOCK position.
6. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 2nd number in the BRAKE CODE.
7. Turn the ignition switch to the LOCK position.
8. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 3rd number in the BRAKE CODE.
9. Turn the ignition switch to the LOCK position.
10. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 4th number in the BRAKE CODE.
11. Turn the ignition switch to the LOCK position.
12. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 5th number in the BRAKE CODE.
13. Turn the ignition switch to the LOCK position.
14. After entering the 5th number, the Immobilizer Indicator light on the dash should flash 5 times and then shut off. The car should now start. This procedure must be repeated each time you turn off the car for more than 10 minutes.

EMERGENCY START PROCEDURE (2001 CIVIC)

1. Make a mechanical key that will work the ignition lock cylinder.
2. Have the customer get the“BRAKE CODE” from the dealer or Honda Customer Relations, you will need the Vehicle Identification Number. This is a five digit number code. Each car has a different “BRAKE CODE” since they are VIN specific.
3. Turn the ignition switch to the ON position (II).
4. Have the BRAKE CODE in front of you. To enter the first number of the BRAKE CODE, set and release the emergency brake the same number of times as the first number in the BRAKE CODE. For example if the first number in the BRAKE CODE is a 2, set and release the emergency brake 2 times.
5. Turn the ignition switch to the OFF position (0).
6. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 2nd number in the BRAKE CODE.
7. Turn the ignition switch to the OFF position (0).
8. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 3rd number in the BRAKE CODE.
9. Turn the ignition switch to the OFF position (0).
10. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 4th number in the BRAKE CODE.
11. Turn the ignition switch to the OFF position (0).
12. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 5th number in the BRAKE CODE.
13. Turn the ignition switch to the OFF position (0).
14. After entering the 5th number, the Immobilizer Indicator light on the dash should flash 5 times and then shut off. The car should now start. This procedure must be repeated each time you turn off the car for more than 10 minutes.